Assignment: Digital I/O with Arduino Boards + Diffuser

Collaborators:

/*
* Serial RGB LED
* ---------------
* Serial commands control the brightness of R,G,B LEDs
*
* Command structure is "<colorCode><colorVal>", where "colorCode" is
* one of "r","g",or "b" and "colorVal" is a number 0 to 255.
* E.g. "r0"   turns the red LED off. 
*      "g127" turns the green LED to half brightness
*      "b64"  turns the blue LED to 1/4 brightness
*
* Created 18 October 2006
* copyleft 2006 Tod E. Kurt <tod@todbot.com
* http://todbot.com/
*/

char serInString[100];  // array that will hold the different bytes of the string. 100=100characters;
// -> you must state how long the array will be else it won't work properly
char colorCode;
int colorVal;

int redPin   = 9;   // Red LED,   connected to digital pin 9
int greenPin = 10;  // Green LED, connected to digital pin 10
int bluePin  = 11;  // Blue LED,  connected to digital pin 11

int redValue = 127;
int greenValue = 127;
int blueValue = 127;

void setup() {
pinMode(redPin,   OUTPUT);   // sets the pins as output
pinMode(greenPin, OUTPUT);  
pinMode(bluePin,  OUTPUT);
Serial.begin(9600);
analogWrite(redPin,   redValue);   // set them all to mid brightness
analogWrite(greenPin, greenValue);   // set them all to mid brightness
analogWrite(bluePin,  blueValue);   // set them all to mid brightness
Serial.println("enter color command (e.g. 'r43 or rrrrrbbg') :"); 
}

void loop () {
//read the serial port and create a string out of what you read
readSerialString(serInString, 100);

processRepeatKeyCommands(serInString, 100);

resetSerialString(serInString, 100);

delay(100);
}

void resetSerialString (char *strArray, int length) {
for (int i = 0; i < length; i++) {
strArray[i] = '\0';
}
}
void readSerialString (char *strArray, int maxLength) {
int i = 0;

if(!Serial.available()) {
return;
}
while (Serial.available() && i < maxLength) {
strArray[i] = Serial.read();
i++;
}
}

void processRepeatKeyCommands(char *strArray, int maxLength) {
int i = 0;

//loop through the string (strArray)
//i = the current position in the string
//Stop when either (a) i reaches the end of the string or
//                 (b) there is an empty character '\0' in the string
while (i < maxLength && strArray[i] != '\0') {
//Read in the character at position i in the string
colorCode = serInString[i];

//If the character is r (red)...
if (colorCode == 'r') {
//Increase the current red value by 10, and if you reach 255 go back to 0
redValue = (redValue + 10) % 255;
analogWrite(redPin, redValue);
Serial.print("setting color r to ");
Serial.println(redValue);

//If the character is g (green)...
} else if (colorCode == 'g') {
greenValue = (greenValue + 10) % 255;
analogWrite(greenPin, greenValue);
Serial.print("setting color g to ");
Serial.println(greenValue);

//If the character is b (blue)...
} else if (colorCode == 'b') {
blueValue = (blueValue + 10) % 255;
analogWrite(bluePin, blueValue);
Serial.print("setting color b to ");
Serial.println(blueValue);
}

//Move on to the next character in the string
//From here, the code continues executing from the "while" line above...
i++;
}
}

//change the value of the red, green, or blue LED according to the command received.
//for example, r240 sets the red LED to the value 240 (out of 255)
void processNumericalCommands(char *strArray) {
//read in the first character in the string
colorCode = serInString[0];

//if the first character is r (red), g (green) or b (blue), do the following...
if( colorCode == 'r' || colorCode == 'g' || colorCode == 'b' ) {
//convert the string to an integer
//(start at the second character, or the beginning of the string '+1')
colorVal = atoi(serInString+1);
Serial.print("setting color ");
Serial.print(colorCode);
Serial.print(" to ");
Serial.print(colorVal);
Serial.println();

if(colorCode == 'r')
analogWrite(redPin, colorVal);
else if(colorCode == 'g')
analogWrite(greenPin, colorVal);
else if(colorCode == 'b')
analogWrite(bluePin, colorVal);
}
}

//compare two strings to see if they are equal
//compares the first 'numCharacters' characters of string1 and string2 to
//see if they are the same
//
//E.g. stringsEqual("hello","hello",5) => true
//     stringsEqual("hello","helaabbnn",3) => true
//     stringsEqual("hello","helaa",5) => false
boolean stringsEqual(char *string1, char *string2, int numCharacters) {
if (strncmp(string1, string2, numCharacters) == 0) {
return true;
} else {
return false;
}
}